阿拉善盟公牛科技开发有限公司
Ordering guide

Ordering guide
Ordering guide
UseProblem
current location:HOME > Order guide > UseProblem
1. Q: When I call the consultation, because of the different regions, the dialects are different, what should I do if I have difficulty communicating?

A: You can use text communication, texting, QQ, fax, etc.

2. Q: What do we do not know what the name of your machine part is?

A: Open the manual, identify it according to the picture, and read the picture.
3. Q: What is the working procedure of the electric blowers, exchangers, and circulating pumps?
Answer: The power supply of the exchanger and the blower is in the same closed loop, so that it can work and stop synchronously, so as to accurately accumulate the total working time of the machine, so that the exchanger can effectively carry out drainage regeneration. The circulation pump only allows it to work for one hour after the processing of the cool skin. Our purpose is to circulate the water inside the machine, to bring the internal scale and water pollution to the sediment under the machine, and then to remove the scale from the sewage valve under the body. Slag. (Note: 10 kilograms of drainage per day, no slag is appropriate)
4. Q: What should I do if there is a sudden power outage during the production process?
A: It is best to prepare a kWh generator for backup, because our power configuration is 220V power supply and 300W power.
5. Q: What should I do if there is sudden water stoppage in the production process of cool skin?
Answer: First, determine if the waterway is closed or blocked. Observe the water level immediately. When the water level reaches the lowest water level (ie 50px above the valve glass tube), the power is turned off and the fire is stopped. When the standby device is not pressed, the ball valve under the manual water injection tank is opened, and the artificial water injection tank is installed to inject the water, which can raise the water level by 75px. (ie: 125px above the center point of the tank) is to extend the use time of each manual water injection.
6. Q: In the process of production of cool skin, the exchanger is draining, and suddenly the tap water is stopped. What should I do?
A: The cold skin processing is processed according to the artificial water replenishment program. But immediately disconnect the power of the switch, let it stop in place, let it continue to drain after running the tap water.
7. Q: What should I do if the exchanger is still regenerating and draining when the cool skin is finished?
A: Turn off the water source, turn off the power supply, and let the exchanger be forced to stop under the current situation. When the cool skin starts to be produced the next day, the water supply and power supply will continue to regenerate the drainage work until it is in normal working condition.
8. Q: The exchanger has been working continuously for more than 72 hours and there is no drainage regeneration. Is this normal?
A: In the process of using your machine, you must have a common-sense concept: depending on the workload of the machine, the machine will work for 72 hours. During this time period, the exchanger must be drained and regenerated, otherwise immediately observe whether the white iron piece corresponding to the regeneration program wheels 3, 6, 9, and 12 is pulled out or immediately consult the Bull Company after-sales department.
9. Q: According to your installer, only two and a half hours of recirculation of the exchanger will be regenerated without draining, but my exchanger has been drained for more than three hours and is still draining. What is the reason?
A: First of all, confirm that the "three hours or more" switch you are talking about is powered on. If the switch is powering down in the drain regeneration state, the exchanger will drain. Please power on immediately, and continue to complete the regeneration process.
10. Q: Would you please re-report the resin protection, replacement time and salt addition of the exchanger?
Answer: The first thing to tell you is that the resin should not be frozen in winter (no more than 2 °C). If the resin is frozen, it will greatly reduce the softening effect of water. According to our machine's water consumption of 80 kg of water per hour, 72 hours of regeneration, if your daily production is 10 bags of flour, the first anniversary of replacement of resin is ideal. According to this workload, the resin replacement time is determined as appropriate. The brine in the brine tank is a standby state and the use of the pre-saturated brine is started when the exchanger drains to regenerate. Salt is added to regenerate the reducing resin in order for the exchanger to soften the water for a long time to cause the resin to age. Each time the drainage is regenerated, it is necessary to add salt once, and each time more than 10 kg of granular salt is added, it is preferable to saturate the brine.
11. Q: What is the reason why the processing of cool skin after the processing of cool skin is getting slower and slower?
A: There are several reasons: 1. The fuel energy is inferior; 2. The combustion is heated by the system; 3. The scale of the water circulation system is blocked. A system check is required.
12. Q: Your installer has to explain that you must open nine descaling holes to clear the scale and slag during the 60-day cycle. My family does not have a water passage. Can you extend the time a little?
A: No, absolutely no, you have to do this if you want to increase your machine's productivity and extend its service life.
13. Q: How long does it take to clean the heated room?
A: Clean up once a month, this is to improve the efficiency of cool skin processing. When cleaning, first open the cleaning hole at the elbow below the pipe, use wooden sticks to pour the dust inside the pipe into the combustion heating room, and then open the dust door under the body to clear all the dust. It is conditional that the combustion chamber can be blown by a strong wind.
14. Q: What is the traffic volume getting smaller and smaller after a long time?
Answer: It is because the hot water preheats the copper pipe after a long time, the scale is clogged, the blocked water pipe is unblocked, and the flow rate is reduced. You need to use the descaling agent to descale the built-in preheated copper pipe immediately, otherwise it will not flow after a long time. It will no longer be able to smooth the descaling and lose this function.
15. Q: Is the filter under the circulation pump still cleaned at any time?
A: Yes, under normal circumstances, clean it once every two months, pay attention to the seal mat can not be lost, copper parts can not be used too much force, otherwise it will damage the parts
16. Q: What should I do if the water level of the glass tube is raised?
A: The range of 50px up and down (250px under the operating cabin) is normal. If it rises suddenly and there is a problem with the float valve from the vent hole, repair and replace the float valve. Note that the float valve outlet is installed vertically downwards.
17. Q: What should I do if the explosion-proof valve suddenly bursts?
A: You don't have to be nervous, because the explosion-proof valve mat is aging and bursting. The standby device is relieved of pressure, and the explosion-proof valve cushion provided by the inner tube of the automobile can be replaced.
18. Q: After steaming the gluten, what is the reason for too much water in the steamer?
A: This is because the airflow control valve at the steamer inlet is not properly adjusted and should be adjusted to a flow rate of 3/1. The method is as follows: first completely close the intake gate valve, determine the handle positioning point, and then open the handle for one week.
19. Q: How can the cold skin made be stained?
A: It should be that your cool leather plate is dirty or the machine running room is dirty and pollutes the cool skin. You need to open the cover to clean the cabin and hatch.

20. Q: If I need to change the factory and move the machine, what should I pay attention to?

A: Read the instructions carefully and watch the CD "Packaging and Installation". You can digitally mark each connection point when disassembling, and check the number when installing. It is important to note that the console is 125px above the hatch.

Copyright:阿拉善盟公牛科技开发有限公司
Meng ICP 16002557 -1 
telephone number:18504830778、18648331236、18504833076 、18504833079 、18504831236 After service telephone:0483-8888488
address:阿拉善盟阿拉善左旗锡林南路祥云豪宸1-2-902室 WeChat public address:gongniulpj Website:www.nmggongniu.com
Copyright © 阿拉善盟公牛科技开发有限公司 All rights reserved ICP record: 蒙ICP备16002557号-1

Keyword: 凉皮机 公牛凉皮机 公牛酿皮机 凉皮机多少钱一台 凉皮机品牌 圆形凉皮机 面皮机 酿皮机 凉皮机厂家 凉皮机哪家好 仿手工凉皮机 米皮机 水蒸汽凉皮机
Keyword: 凉皮机 公牛凉皮机 公牛酿皮机 凉皮机多少钱一台 凉皮机品牌 圆形凉皮机 面皮机 酿皮机 凉皮机厂家 凉皮机哪家好 仿手工凉皮机 米皮机 水蒸汽凉皮机
Sales department telephone number:

Contact:0483-8888188

Contact:18504830778

Contact:18648331236

Contact:18504833076

Contact:18504833079

Contact:18504831236

WeChat service number